Devices You Need to Install a New Bathtub
Devices You Need to Install a New Bathtub
Blog Article
Everybody has their own way of thinking when it comes to Installing A Bathtub.
Installing a tub isn't specifically rocket science, however it does call for strong plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old bathtub with a new one is likewise a reasonably hard project. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall surface to remove the old tub and also position the new tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to move out the old tub as well as set in the brand-new one. See to it you have actually certified on your own for the job as well as fit trying it. Rather than hiring a specialist to take control of a halfway-completed task, it is better to think about using one prior to you begin. Chances are you may require a specialist plumber to make tube links.
This article will assist you mount a brand-new bath tub in your bathroom if you have already purchased a new bathtub and also do not require to transform the setup of your previous water supply pipes.
Your tools as well as material checklist must make up the following:
Preparing for the Installation
Firstly, the supporting frame supplied with the bath should be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the faucet includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath need to currently prepare to be suited its final position.
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of removing the existing faucets can be rather problematic as a result of the limited gain access to that is frequently the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a towel all set for the staying water that will originate from the pipes. Once the supply pipelines have been removed, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary taps from transforming throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing substance.
Before moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Tub
Making use of the two wood boards under its feet, place the tub in the required setting. The wood boards are useful in uniformly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bath tub until the level reads degree.
To install taps, fit all-time low of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Activate the water supply as well as examine all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leaks.
Lastly, deal with the bath paneling as explained in the supplier's instruction manual. Tiling as well as securing around the bathtub ought to wait till the bath tub has been utilized at the very least once as this will settle it right into its last position.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in location in between the faucet and also the sink. Secure the tap in place with the producer supplied backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap connectors. The former type ought to be linked to the tap ends first, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall between the bath and the tiling, bring about issues with moisture as well as possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes and cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub is in use. The sealer can crack fairly very early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was introduced to that article about Tools You Need to Install a New Bathtub from a friend on a different web blog. Enjoyed reading our article? Please share it. Let others locate it. Kudos for your time. Kindly visit our site back soon.
Contact Us
Report this page